Contact Form

Single Crystal NMC613 Cathode Material — High Tap Density Powder for Pouch and Cylindrical Cells

PRODUCT PARAMETERS

Chemical Composition

Ni:Co:Mn 60:10:30 (mol%)
Li/M molar ratio 1.04 ± 0.03
Crystal structure Layered single crystal
LiOH 269 ppm
Li2CO3 1,749 ppm

Physical Properties

Tap density 2.29 g/cm3 (spec >=1.80)
Specific surface area (BET) 0.7902 m2/g (spec <=1.00)
Moisture <500 ppm
pH (slurry) 11.61

Particle Size Distribution

D10 2.06 um
D50 3.67 um (spec 3.70±1.0)
D90 6.32 um
Dmax 9.96 um

Electrochemical Performance

Discharge specific capacity 195.4 mAh/g (spec >190)
Initial coulomb efficiency >86%
Test voltage window 3.0 – 4.4 V

Fe, Cu and Na are reported in the batch COA.

Description
About Us
FAQs
Request A Quote

Description

Gelon’s NMC613 cathode material gives high-energy lithium-ion cells a dense, uniform cathode powder. This NMC613 cathode material combines a 60:10:30 Ni:Co:Mn molar ratio with a measured tap density of 2.29 g/cm³. As a result, cell makers can pack more active material into pouch, cylindrical, prismatic and polymer formats. Gelon ships the powder as model GN-SC60, so you can use it in both laboratory coin-cell research and pilot production. In short, it suits any process where first-cycle efficiency and electrode density matter.

Gelon produces the material under strict chemical composition control. The team holds Li/M at 1.04±0.03 and keeps residual alkali and moisture within tight limits. In addition, every batch ships with a certificate of analysis, so you can verify the numbers before the powder reaches your coating line. The single-crystal structure also resists particle cracking during cycling, while the high tap density supports denser electrodes and better volumetric energy density. Whether you screen cathode candidates in a university lab or qualify a supplier for consumer cells, this grade gives you a repeatable starting point with batch-specific data.

Technical Specifications

Technical Specifications

Specification vs. Measured Batch Data

Nominal specification and a representative measured batch shown side by side. Bold figures are measured values.

ParameterNominal / SpecificationMeasured (typical batch)
Ni:Co:Mn molar ratio60:10:30 mol%60:10:30 mol%
Li/M molar ratio1.04 ± 0.031.04
Crystal structureLayered single crystalFully single crystal
Tap density≥ 1.80 g/cm³2.29 g/cm³
Specific surface area (BET)≤ 1.00 m²/g0.7902 m²/g
Moisture content< 500 ppmSee batch COA
pH (slurry)—11.61
D10—2.06 μm
D503.70 ± 1.0 μm3.67 μm
D90—6.32 μm
Dmax—9.96 μm
LiOH—269 ppm
Li₂CO₃—1,749 ppm
Discharge specific capacity> 190 mAh/g195.4 mAh/g
Initial coulomb efficiency> 86%> 86%
Test voltage window3.0 – 4.4 V3.0 – 4.4 V
Fe, Cu, Na impuritiesUltra-low, controlledReported in batch COA
Engineer’s note: Two numbers here matter more than the headline capacity. First, a D90 of 6.32 μm with a Dmax below 10 μm points to a narrow, clean particle-size distribution. That means fewer coarse clumps to cause coating defects or micro-shorts, along with more predictable slot-die and doctor-blade processing. Second, low residual alkali (269 ppm LiOH, 1,749 ppm Li₂CO₃) plus moisture below 500 ppm cut slurry gelation and gas generation during formation. Taken together, these figures turn a good first-cycle number into an electrode that stays stable in production.

Electrochemical Performance

Gelon tests this NMC613 cathode material within a 3.0 – 4.4 V window, and it delivers a typical discharge specific capacity of 195.4 mAh/g against a specification above 190 mAh/g. Moreover, initial coulomb efficiency stays consistently higher than 86%. That first-cycle efficiency matters commercially: the first charge consumes less lithium, so cell designers can allocate more capacity to usable energy instead of covering losses.

The layered single-crystal architecture also limits cracks between grains, and that helps cycling stability. Polycrystalline high-nickel cathodes often degrade through such cracks during repeated charge and discharge. However, exact cycle-life data depend on the batch and the cell design, so we share them on request together with the test report. We never publish a cycle count without its test conditions. If you need capacity-retention curves under a specific voltage window, C-rate or temperature, ask for the COA and the matching cycling dataset.

Morphology & Particle Size (NCM601030)

This grade stands out for its complete single-crystal structure. Unlike secondary clumps built from many small primary particles, each powder particle forms a single crystal. That structure stays mechanically robust during charging and discharging, so it develops far fewer micro-cracks. For this reason, buyers pick single-crystal NMC613 for long-life and high-voltage applications.

Gelon also controls particle size tightly. D10 sits at 2.06 μm, D50 at 3.67 μm and D90 at 6.32 μm, with Dmax below 10 μm. A narrow distribution improves electrode uniformity: fine particles fill the gaps between larger ones, which raises packing density and helps the powder hit its 2.29 g/cm³ tap density. In addition, the BET surface area of just 0.7902 m²/g limits unwanted electrolyte contact and side reactions at the particle surface.

Quality Assurance & Packaging

Gelon verifies consistency batch by batch. Each shipment of NMC613 cathode material includes a certificate of analysis that covers chemical composition, particle-size distribution, tap density, BET surface area, moisture and residual lithium. The company also keeps trace metals (Fe, Cu, Na) at ultra-low levels and reports them in the batch COA rather than estimating them. Customers can request CE certification documents at any time.

Standard packaging uses cartons, and the minimum order quantity is 1 kg. That size works for formulation screening, while a supply capacity of 500 kg per month supports scaled programs. Typical delivery takes 10 working days. Since the powder attracts moisture, Gelon packs it to survive transit. On receipt, store it sealed in a dry environment and follow the batch COA and SDS for handling.

Applications

Applications

From Coin Cell to Pilot Line

▤
Pouch & Aluminum-Shell Cells
Soft-pack and aluminum-shell lithium-ion cells.
◉
Steel-Shell & Polymer
Steel-shell and polymer lithium batteries.
◎
Lab Coin Cells
University labs and material research studies.
▣
Consumer Batteries
Electronics needing high volumetric energy density.
⬡
EV Pilot Lines
Power-battery development with single-crystal cathodes.
↻
Lab-to-Pilot Transfer
One grade from screening through pilot production.

The grade works with both solvent-based and water-based electrode processing, subject to your own slurry and binder checks. Its balanced 6:1:3 nickel-cobalt-manganese chemistry also makes it a practical choice when you want more energy than NCM523 without taking on the thermal-management demands of very high-nickel grades.

NMC Family Positioning

Within Gelon’s cathode portfolio, this single-crystal grade complements the broader NMC/NCM cathode powder range, which covers 523, 622 and 811 compositions. If you compare options, the NMC622 T61R powder offers a different balance of nickel content and capacity, while the higher-nickel 811 grade targets maximum energy. This NMC613 sits between them: moderate nickel, high tap density and a single-crystal structure built for cycle stability. We keep the comparison short on purpose, because the family page carries the full selection matrix. Consequently, this page stays focused on measured data and pricing for one grade.

Why Choose Gelon

  • Complete single-crystal structure — resists particle cracking and supports long cycle life
  • High tap density (2.29 g/cm³) — enables denser electrodes and higher volumetric energy
  • Low residual alkali and moisture — fewer side reactions and more stable processing
  • Documented quality — a batch-specific COA with every shipment, not generic datasheet claims
  • Broad compatibility — works with pouch, cylindrical, prismatic and polymer cells, plus lab R&D
FAQ

Frequently Asked Questions

Q1. How much does NMC613 cathode material cost per kg?
The reference price is 110–115 USD per kg, with a minimum order of 1 kg. This is a guide range, and the final quote depends on order volume, packaging and destination. So please send your required quantity for a firm price. You can also arrange samples for evaluation on request.
Q2. What is the minimum order quantity, and can I get a sample?
MOQ is 1 kg, which suits coin-cell screening and small-batch mixing. Gelon can supply sample quantities for lab evaluation; tell us your test plan and we will confirm what we can provide. For production programs, our monthly capacity reaches 500 kg.
Q3. Do you provide a COA or test report for the NCM601030 powder?
Yes. Every batch ships with a certificate of analysis listing composition, Li/M ratio, D10/D50/D90, tap density, BET surface area, moisture and residual lithium (LiOH, Li₂CO₃). You can also request Fe, Cu and Na results plus cycling data under agreed test conditions.
Q4. Which cell types is this cathode material suitable for?
The powder works in soft-pack, aluminum-shell, steel-shell and polymer lithium-ion cells, as well as laboratory coin cells. It also fits consumer batteries and EV power-cell development where single-crystal stability and high electrode density matter. Because the same grade serves both research and production, you can carry a formulation from coin-cell screening to pilot scale without changing cathode supplier.
Q5. What payment terms and delivery options are available?
Standard lead time runs 10 working days, and cartons are our usual packaging. We accept L/C, D/A, D/P, T/T and Western Union. Shipping terms and freight depend on the destination, so contact our team with your port or address for a landed-cost quote.
Q6. How should the powder be stored and handled?
NMC613 powder attracts moisture. Keep it sealed in its original packaging in a dry place and avoid long exposure to humid air. For storage temperature, shelf life and handling steps, refer to the batch COA and safety data sheet that come with your order.

About Us

Lithium battery equipment factory display
OUR battery equipment's PROJECT
Lithium battery equipment factory work scenario
Lithium battery equipment installation scenario
Certificates:Integrated gas purifier system and PLC controller
used for keeping inert gases by recirculation

FAQs

Please send us your purchase order by email or call us sales , then we can make the proforma invoice under your request .We need to know the following information for your order before sending your PI
1) Product information–quantity ,specification(size,technological if needed and packing requirements ect.)
2) Delivery time required.
3) Shipping information–Company name, detail address, phone number, destination sea port .
4) Forwarder’s contact details if there’s any in China

It takes 1-5 days for sample order or part of inventoryequipment (depending on the requirements of the order)10-30 days for mass production orders(depending on order requirements, etc.)

Please tell us :

What's your application and your special requestof the products ?

Better to let us know what's your expect performance ?

Handmade wooden box layers of protectionDelivery real shot

We accept EXW, FOB, CIF,DAP etc. You can choose the one whichis the most convenient or cost effective for you.

There is a English manual for each equipment that will show youhow to use the machine If there is still any questions,Please feel free to contact us by online service,such as e-mail/skype/phone/whatsapp/wechat at any time.

Lithium Battery Equipment Production Process Demonstration
  • The guarantee period : One year

LiBatteryEquip is a professional supplier specializing in complete Battery Laboratory Equipment,Lithium Battery Production Line, and Battery Testing Equipment. With over 20 years of experience in lithium battery material production, and battery equipment manufacturing, we provide customized lithium battery laboratory and pilot production line solutions for various research institutions and enterprises to meet their diverse needs. Our technical and management team possesses more than 20 years of expertise in the battery-related industry, consistently committed to delivering superior products and comprehensive services to our clients.

REQUEST A QUOTE

REQUEST A QUOTE